Marine Paint

Super Gloss
One-pack. Superior high-gloss enamel based on siliconized alkyd resin. Excellent gloss retention and very good weather resistance. Optimum flow, non-yellowing. Minimal dirt pick-up. 750ml.

Application
On wood, steel, aluminium, and GRP, above the waterline, both inside and out. For new work in combination with the appropriate primers or direct on pre-treated GRP. Also useful for maintaining existing, intact, one-pack enamels. Available in 16 colours.

Hempel Prop Primer is an anti-corrosive primer which acts as a primer on a large variety of substrates. Particulary recommended as a primer for propellers, outboards and outdrives. Fast drying. Products has very good adherence to steel and other metals, very easy to apply. Matt finish.

Hempel Mille Drive is for use below the waterline on propellors, outboards and outdrives. Avaliable in Volvo Grey and Black.

This is a high strength burnishable antifouling which gives a smooth racing finish, offering all round competitive performance. Formulated especially for powerboats, racing yachts and vessels which are mud berthed, may also be used on vessels that are dry sailed. It is suitable for all substrated except aluminium, for use below the waterline.

Size: 750ml
Coverage: 13.5 m2
Thinners: No. 3

A two pack high performance epoxy priming and undercoating system, for use on glass fibre, wood, steel and aluminium. This product has an outstanding corrosion, impact and water resistance qualities both above and below the waterline. It can be used for osmosis protection when application takes place at low temperatures. Epoxy primer undercoat is an excellent protective coating between the substrate and PolyGloss topcoat, ensuring longevity of the system.

Coverage: 8.5 m2
Thinners: No. 5

A two pack polyurethane and epoxy system giving a high gloss finish which is extremely durable and resistant to ultra-violet degradation and abrasion. Polygloss is well known for its ease of application and its high performance properties. Polygloss should be applied at temperatures of 10'C and above. For use above the waterline.

Trilux Prop O Drev is an antifouling specially formulated for aluminium and stainless steel outdrives, outboard legs, propellers and stern gear. In addition to offering effective antifouling protection, its smooth hard finish minimises drag helping to improve propulsion efficiency. Designed as an easy to use aerosol, the spray application.

PREPARATION
Prime bare metal and factory enamelled surfaces with two coats VC Prop O Drev Primer. This is essential on aluminium or alloy as Trilux Prop O Drev is not suitable for direct application. For best results on previously antifouled surfaces remove existing paintwork. Alternatively wet abrade with 240 grade paper.

Coverage: Approx 1 m2 per can
Clean up: VC General Thinner

International Interstrip. Interstrip AF is specially formulated to effectively remove old layers of antifouling from glassfibre, steel, aluminium and wooden boats. Unlike many paint strippers, Interstrip AF will not harm gelcoat. It is a safe and cost effective method of removing antifouling, saving time and effort. Important: Interstrip AF is thixotropic making it easy to use even on vertical surfaces.

Product Description:
Pre-Kote is an undercoat for one pack finishes such as Toplac, Brightside® and Interlux® Super. Pre-Kote offers excellent obliteration which in turn, allows for easy colour changing. Pre-Kote is designed around tough, flexible resins which means it is long lasting and easy to apply and rub down, providing a smooth base for the finishing coat. It is available in a range of colours to complement the topcoat.
Area: Above the waterline
Available in: Blue Grey, Red, Dark Blue or White

Finish/Sheen: Low-sheen

Thinner/ Cleaner: YTA800 Thinners No.1
Number of Coats: 1-2.

Method of application: Brush, Roller, Airless or Conventional Spray

Product Description:
Primocon is a grey, tar-free, quick drying, conventional primer for all substrakes underwater. Also suitable as a barrier/ sealer coat over incompatible or unknown antifoulings. Can be used under all International antifoulings. Not suitable to be overcoated with 2-component solvent-based paints.
Area: Below the waterline

Finish/Sheen: Matt

Thinner/ Cleaner: YTA085 Thinners No.3
Number of Coats: 1-5 by brush or roller depending on the substrake.

Method of application: Brush, Roller or Airless Spray

Quick drying conventional primer for wood, steel and aluminium alloy above the water.

IMPORTANT
Do not overcoat with 2 component solvent based products.

PREPARATION
For wood ensure bare wood is clean and dry. Apply UCP or alternatively 1 coat of Yacht Primer thinned 10-15% with Thinners No. 1 to ensure penetration and adhesion. Oily woods e.g teak wash surface with Thinners No. 1 allow to dry. Thin first coat of Yacht Primer 15-20% prior to application. Steel, grit blast to Sa 2 half to 3. An angle grinder can be used for small areas. Alumminium, clean and degrease with Yacht Line Super Cleaner. For better adhesion, mechanically abrade with aluminium compatible sandpaper or low pressure grit blast using aluminium oxide. Pre

A satin finish varnish designed primarily for interior use. The polyurethane resin gives a tough finish resistant to hot water, mild acids and alkalis. The quick drying formulation minimises dust contamination.

PREPARATION
Previously varnished wood in good condition clean with thinners. Sand with 280-320 grade wet or dry paper. Remove sanding dust with thinners. In poor condition all previous coating should be removed. Bare wood sand smooth with 80-180 and then 280 grade paper. Clean surface y brushing, dusting or wiping - if wiping with solvent allow to dry completely before applying the first coat of varnish. Priming bare wood apply Intertox or UCP. If UCP has been omitted thin the first coat by 10-15% with Thinners No. 1.

APPLICATION
Apply a minimum of three full bodies coats, more if using a roller.

Coverage: 25m2 / 2.5lt
Thinners: Thinners No. 1

A traditional tung oil based yacht varnish for classic yachts. Suitable for all internal and external wood. Schooner contains UV absorbers for a long lasting finish and its easy to brush formulation gives a deep rich gloss.

IMPORTANT
Stir well before use. Avoid damp conditions. Only use the recommended thinners.

Goldspar is a high quality, high gloss clear polyurethane varnish with added UV protection. The polyurethane resin gives a tough finish for interior and exterior use, resistant to hot water, mild acids and alkalis. The quick drying formulation minimises dust contamination. Goldspar is a clear high gloss finish which lets the natural colour of the wood show through.

PREPARATION
Previously varnished wood in good contition: clean with Super Cleaner. Sand with 280-320 grade paper. Remove sanding dust with Thinners No. 1. In poor conditions all previous coating should be removed. Bare wood sand smooth with 80-180 and then 280 grade paper. If wiping with thinner allow to dry completely before applying the first coat of varnish. Priming bare wood apply UCP. If UCP has been ommited thin the first coat by 10-15% with Thinner No. 1.

APPLICATION
Apply a minimum of three unthinned coats, more if using a roller.

Coverage: 4.5m2 / 375ml, 9m2 / 750ml
Thinners: No. 1

Special purpose thinners. For use with UCP and when spraying some 2-pack polyurethanes.

Thinner and equipment cleaner for 2-pack polyurethane type International products and UCP.

Suitable for use with:
Undercoats
Finishes
Varnishes
Two part products

Thinner and equipment cleaner for antifoulings (except VC). Not suitable for thinning Micron Optima.

Suitable for use with:
Antifouling
Primers
One part products

General purpose thinner and equipment cleaner for 1 pack paints and varnishes (except Brightside).

Suitable for use with:
Primers
Undercoats
Finishes
Varnishes
One part products

Ultimate Performance two-part polyurethane gloss. Extremely hardwearing. Longest lasting gloss. Best UV resistance. Easy 2:1 mix ratio. For detailed product information refer to yachtpaint.com.

WARNING
Contains isocyanates - Read health and safety data. If spraying, contact International.

PREPARATION
(Note: do not apply over one part paints, flexible constructions or in immersed areas) Previous painted surfaces in good condition; was with Super Cleaner then rinse with fresh water and allow to dry. Abrade (220-320 grade). New surface requiring priming.

GRP: No priming needed

A fully flexible antifoul for use on PVC material.

Can also be used on non-flexible surfaces such as GRP. Hull and tubes can be protected on your RiB with just one product.

Developed using unique pseudo-organic technology
Extensively tested - keeps virtually all hulls free from growth of algae, crustaceans and othe unwelcome marine life

Includes copper, linked with our own extremely low friction technology SP54 offers a unique solution to an age old marine problem

Available in 1 litre tins

Coverage: 1 ltr allows 2 full coats on an average 2.9m boat. Allow 2 hours between coats and leave overnight before launching craft.
No primer needed.

Danboline provides a hight opacity, hardwearing high sheen finish which is easily cleaned. It can be applied to wood, steel aluminum or GRP after suitable priming. The special high opacity formulation gives a high sheen finish that can be applied to wood, steel, alloy or GRP after suitable priming.

PREPARATION
Previously painted surfaces in good condition; wash with Yacht Line Super Cleaner, rinse with fresh water and allow to dry. Abrade with 180-280 grade paper. If in poor condition all damaged coatings should be removed and the substrate primed.

PRIMING
All preperation for bare substrates is covered on the appropriate primer label.

Bare Wood:
Yacht Primer or UCP

Steel:
Yacht Primer or Interprotect.

Aluminium:
Etch Primer then either Yacht Primer or Interprotect.

GRP:
No priming necessary but wash as above and abrade with 180-220 grade paper. Particular attention should be given to the reverse side of moulded GRP.


APPLICATION
Sand the primer using 180-280 grade wet or dry paper. Remove dust with a dust wipe. Apply 1-2 coats in dry, well ventilated conditions.

Coverage: 8 m2 / 750ml
Thinners: No. 1

For added protection against moisture absorption and osmosis in bilges, use Gelshield 200.

Interdeck provides an excellent slip resistant finish. It contains a fine aggregate and will apply easily on all substrates. The tough Polyurethane resin protect decks against everyday wear and tear.

IMPORTANT
Stir well before use

PREPARATION
Previously painted surfaces in good condition wash with Yacht Line Super Cleaner, rinse with fresh water and allow to dry. Abrade with 220-320 grade paper. If in poor condition all previous coatings should be removed and the substrate primed.

PRIMING
All preparation for bare substrates is covered on the appropriate primer label.

Bare Wood:
Yacht Primer or UCP

Steel:
Yacht Primer or Interprotect

Aluminium:
Etch Primer then either Yacht Primer or Interprotect.

GRP:
No priming necessary but wash as above and abrade with 180-220 grade paper. If any filing is required use the appropriate product from the Interfill range.


APPLICATION
Sand the primer using 180-280 grade wet or dry paper. Remove dust with a dust wipe. Apply 1-2 coats in dry ventilated conditions.

Coverage: 7 m2 / 750ml
Thinners: No.1

For best results either stipple by brush or use a mohair roller.

Toplac is a premium gloss marine enamel for all substrates for use above the waterline. It is exceptionally easy to apply by brush, roller or pad and contains UV filters for increased durability. Its unique chemical structure enables Toplac to outperform all traditional finishes in terms of gloss and gloss retention.

IMPORTANT
Stir well before use. Not suitable for permanently immersed surfaces.

PREPARATION
Previously painted surfaces in good condition, wash with Yacht Line Super Cleaner, rinse with fresh water and allow to dry. Abrade with 280-320 grade paper. In poor condition; all previous coatings should be removed and the substrate primed.

PRIMING
All preperation for bare substrates is covered on the appropriate primer label.

Bare Wood:
Yacht Primer or UCP

Steel:
Yacht Primer or Interprotect

Aluminium:
Etch-Primer then either Yacht Primer or Interprotect

GRP:
No priming necessary but wash as above and abrade with 180-220 grade paper. Use Pre-Kote undercoat


APPLICATION
Sand the undercoat smooth with 320-400 grade wet or dry paper. Remove dust with a dust wipe. Apply 1-2 coats in dry, well ventillated conditions.

Coverage: 9m2 / 750ml
Cleaning/ Thinners: Thinners No. 1

To improve depth of colour and opacity of lighter colours, the first coat can be a 50:50 mix of finish and undercoat. Two further coats of finish should be then applied.

Avoid applying late in the evening as condensation can cause loss of gloss overnight.

For best results when applying by roller, smooth off witha pad or brush.

In warm or windy conditions up to 10% thinners No. 1may be added to ease application.

Brightside is a superior quality polyurethane gloss yacht enamel for all aubstrates above the waterline. Its Teflon® containing formula produces an easy-clean, tough finish, resistant to abrasions, stains, chemicals and dirt.

IMPORTANT
Stir well before use. Do not use on permanently underwater areas.

PREPARATION
Painted surfaces if sound wash with Yacht Line Super Cleaner, fresh water rinse and allow to dry. Abrade with 280-320 grade paper. If unsound remove coating and prime surface.

Bare Wood:
Yacht Primer or UCP

Steel:
Yacht Primer or Interprotect

Aluminium:
Etch Primer then either Yatch Primer or Interprotect

GRP:
No prior priming necessary but wash as above and abrade with 180-220grade paper.

All Substrates:
Use Pre-Kote undercoat.


APPLICATION
Sand undercoat with 320-400 grade wet or dry paper. Remove dust. Apply minimum 2 coats of Brightside in dry, well ventilated conditions. Avoid applying late in the evening to avoid effects of condensation.

Coverage: 10 m2 / 750ml
Cleaning / Thinners: Thinners No. 333